Re: Problème de configuration SIOC et Offsets pour FMC PMDG
Posté: Ven 19 Oct 2012 21:43
Si je lis le manuel de la carte, tu dois programmer une frappe clavier pour chaque touche de ton FMS
C'est dans "assign your keys"
Ensuite tu dois spécifier le nom exact de la fenêtre où le programme enverra les touches clavier
donc il faut mettre l'intitulé de la fenêtre de FS.
Normalement avec ça, ta carte doit envoyer les bonnes frappes clavier à FS et tu dois pouvoir
les récupérer dans FSUIPC sous "key pressed" et les assigner à un évènement PMDG qui doit
apparaître dans la liste.
BOB
Encoder_keys.exe:
This software is a keyboard emulator that reads the keys strokes from our USB Keys. When we
start the software, it automatically will minimize himself in the task bar (Tray) with an icon
representing a keyboard), we can maximize it and it will show the last pressed key and the
Device number.
First thing to do is configure the encoder_keys.ini, to have access to the board.
File parameters:
MUSB=No
We will put YES if we have more than one Usb Keys installed.
DeviceUSB=XXXX
We will put the USB port that USBcheck.exe shows us (in our case it is 2048).
Window = “a.txt - Notepad”
We will write in this line the name of the window where we want the key stroke to be addressed.
To do it the window must be always active, never minimized or behind another window.
[Assign your keys]
#1=A
#2=B
#3=C
…
#88=
This way we will send the keys codes and the keys sequences.
In the upper example, we clearly see that if we press key 1 (#1, pin7+pin35, A1 in the matrix),
we will send to the assigned and activated window the "A", pressing the 2 key (#2, pin8+pin35,
A2 in the matrix) we will send the "B", etc.
Combined key strokes as CTRL, ALT, etc. will be sent with special key codes that will be seen
at the end of this manual.
C'est dans "assign your keys"
Ensuite tu dois spécifier le nom exact de la fenêtre où le programme enverra les touches clavier
donc il faut mettre l'intitulé de la fenêtre de FS.
Normalement avec ça, ta carte doit envoyer les bonnes frappes clavier à FS et tu dois pouvoir
les récupérer dans FSUIPC sous "key pressed" et les assigner à un évènement PMDG qui doit
apparaître dans la liste.
BOB
Encoder_keys.exe:
This software is a keyboard emulator that reads the keys strokes from our USB Keys. When we
start the software, it automatically will minimize himself in the task bar (Tray) with an icon
representing a keyboard), we can maximize it and it will show the last pressed key and the
Device number.
First thing to do is configure the encoder_keys.ini, to have access to the board.
File parameters:
MUSB=No
We will put YES if we have more than one Usb Keys installed.
DeviceUSB=XXXX
We will put the USB port that USBcheck.exe shows us (in our case it is 2048).
Window = “a.txt - Notepad”
We will write in this line the name of the window where we want the key stroke to be addressed.
To do it the window must be always active, never minimized or behind another window.
[Assign your keys]
#1=A
#2=B
#3=C
…
#88=
This way we will send the keys codes and the keys sequences.
In the upper example, we clearly see that if we press key 1 (#1, pin7+pin35, A1 in the matrix),
we will send to the assigned and activated window the "A", pressing the 2 key (#2, pin8+pin35,
A2 in the matrix) we will send the "B", etc.
Combined key strokes as CTRL, ALT, etc. will be sent with special key codes that will be seen
at the end of this manual.