aircockpit.com

bonjour à tous,
voilà, je suis en train de calibrer ma gauge flaps open cokpit pour 737.
j'ai calé les indicateurs de flaps comme il faut et cela fonctionne avec ifly et fsx, mais j'ai un problème d'association des deux leds transit et extend qui ne s'allument pas quand il faut..

voici mon script:

Var 0000, Value 0
{
&ind_le_extend = 0
&ind_le_trans = 0
}

Var 0001, name servo_flaps, Link USB_SERVOS, Output 1, PosL 0, PosC 511, PosR 1023

Var 0002, name flaps_fsuipc, Link FSUIPC_IN, Offset $0BE0, Length 4
{
L0 = &flaps_fsuipc
L0 = ABS L0
IF L0 = 0
{
&ind_le_extend = 0
&ind_le_trans = 0
}
ELSE
{
L1 = 0
&ind_le_trans = 1
IF L0 = 409
{
L1 = 1
&ind_le_trans = 0
}
IF L0 = 819
{
L1 = 1
&ind_le_trans = 0
}
IF L0 = 2047
{
L1 = 1
&ind_le_trans = 0
}
IF L0 = 4095
{
L1 = 1
&ind_le_trans = 0
}
IF L0 = 6143
{
L1 = 1
&ind_le_trans = 0
}
IF L0 = 10239
{
L1 = 1
&ind_le_trans = 0
}
IF L0 = 12287
{
L1 = 1
&ind_le_trans = 0
}
IF L0 = 16383
{
L1 = 1
&ind_le_trans = 0
}
&ind_le_extend = L1
}
L2 = L0
C0 = L0 >= 0
C1 = L0 <= 409
IF C0 AND C1
{
&flaps_low_val = 0
&flaps_high_val = 409
&servo_high_val = 154
&servo_low_val = 236 // 0 and 1
}
C0 = L0 >= 409
C1 = L0 <= 819
IF C0 AND C1
{
&flaps_low_val = 409
&flaps_high_val = 819
&servo_high_val = 236
&servo_low_val = 381 // 1 and 2
}
C0 = L0 >= 819
C1 = L0 <= 2047
IF C0 AND C1
{
&flaps_low_val = 819
&flaps_high_val = 2047
&servo_high_val = 381
&servo_low_val = 502 // 2 and 5
}
C0 = L0 >= 2047
C1 = L0 <= 4095
IF C0 AND C1
{
&flaps_low_val = 2047
&flaps_high_val = 4095
&servo_high_val = 502
&servo_low_val = 600 // 5 and 10
}
C0 = L0 >= 4095
C1 = L0 <= 6143
IF C0 AND C1
{
&flaps_low_val = 4095
&flaps_high_val = 6143
&servo_high_val = 627
&servo_low_val = 729 // 10 and 15
}
C0 = L0 >= 6143
C1 = L0 <= 10239
IF C0 AND C1
{
&flaps_low_val = 6143
&flaps_high_val = 10239
&servo_high_val = 729
&servo_low_val = 841 // 15 and 25
}
C0 = L0 >= 10239
C1 = L0 <= 12287
IF C0 AND C1
{
&flaps_low_val = 10239
&flaps_high_val = 12287
&servo_high_val = 841
&servo_low_val = 950 // 25 and 30
}
C0 = L0 >= 12287
C1 = L0 <= 16383
IF C0 AND C1
{
&flaps_low_val = 12287
&flaps_high_val = 16383
&servo_high_val = 950
&servo_low_val = 1023 // 30 and 40
}
&servo_calc = &servo_low_val - &servo_high_val
&flaps_calc = &flaps_high_val - &flaps_low_val
&flaps_val = L0 - &flaps_low_val
&servo_val = &servo_calc * &flaps_val
&servo_val = &servo_val / &flaps_calc
L1 = &servo_high_val + &servo_val
&servo_flaps = L1
}

Var 0003, name servo_val

Var 0004, name flaps_calc

Var 0005, name servo_calc

Var 0006, name flaps_val

Var 0007, name flaps_low_val

Var 0008, name flaps_high_val

Var 0009, name servo_high_val

Var 0010, name servo_low_val

Var 0011, name ind_le_extend, Link IOCARD_OUT, Output 11

Var 0012, name ind_le_trans, Link IOCARD_OUT, Output 12


merci pour votre aide

bonne journée